Grogg Posted May 17, 2023 Share Posted May 17, 2023 Really I'm not procrastinating, delaying or putting off finally painting my Rock Socker body shell. I've measured, marked out, and cut the mountings for fuel tanks to be mounted on either side of the body shell, and mounted them temporarily, here's what it will look like; A fuel tank will be mounted on the same place on the other side of the body shell. I'm currently tweaking the paint masks that I've custom made in G.I.M.P. so that I can paint everything instead of using stickers, just with the cost of printer ink - over £30 for the black ink cartridge for my printer alone it's actually by £25 for me to buy my printer again brand new rather than to replace all of the ink cartridges it takes, so I'm trying to minimise the amount of not needed or test prints for sizing, not to mention that the Tamiya 15cm by 18cm masking sheets for printing on are not cheap, they're a quid each, so I want to use as few of the Tamiya masking sheets as possible. Hopefully my next post to this thread will be of at least the body shell starting the painting process, even if it's just masked up for the first colour to be painted. Quote Link to comment Share on other sites More sharing options...
Grogg Posted May 17, 2023 Share Posted May 17, 2023 Really I'm not procrastinating, delaying or putting off finally painting my Rock Socker body shell. I've measured, marked out, and cut the mountings for fuel tanks to be mounted on either side of the body shell, and mounted them temporarily, here's what it will look like; A fuel tank will be mounted on the same place on the other side of the body shell. I'm currently tweaking the paint masks that I've custom made in G.I.M.P. so that I can paint everything instead of using stickers, just with the cost of printer ink - over £30 for the black ink cartridge for my printer alone it's actually by £25 for me to buy my printer again brand new rather than to replace all of the ink cartridges it takes, so I'm trying to minimise the amount of not needed or test prints for sizing, not to mention that the Tamiya 15cm by 18cm masking sheets for printing on are not cheap, they're a quid each, so I want to use as few of the Tamiya masking sheets as possible. Hopefully my next post to this thread will be of at least the body shell starting the painting process, even if it's just masked up for the first colour to be painted. 2 Quote Link to comment Share on other sites More sharing options...
Rustic Ade Posted May 17, 2023 Share Posted May 17, 2023 2 hours ago, Grogg said: Really I'm not procrastinating, delaying or putting off finally painting my Rock Socker body shell. I've measured, marked out, and cut the mountings for fuel tanks to be mounted on either side of the body shell, and mounted them temporarily, here's what it will look like; A fuel tank will be mounted on the same place on the other side of the body shell. I'm currently tweaking the paint masks that I've custom made in G.I.M.P. so that I can paint everything instead of using stickers, just with the cost of printer ink - over £30 for the black ink cartridge for my printer alone it's actually by £25 for me to buy my printer again brand new rather than to replace all of the ink cartridges it takes, so I'm trying to minimise the amount of not needed or test prints for sizing, not to mention that the Tamiya 15cm by 18cm masking sheets for printing on are not cheap, they're a quid each, so I want to use as few of the Tamiya masking sheets as possible. Hopefully my next post to this thread will be of at least the body shell starting the painting process, even if it's just masked up for the first colour to be painted. Waiting with baited breath for this. Got my first spray job to do once I've done all the technical stuff so love seeing what and how folk do stuff. Quote Link to comment Share on other sites More sharing options...
Popular Post Kpowell911 Posted May 17, 2023 Popular Post Share Posted May 17, 2023 Had a few hours free this evening, Id like to say its cause I finished work early, but I did leave my house at 520am so Id hope so. All Tamiya love again (shock!) Oil shocks for the Humble TL-01. A servo for the SRX Full electrics for the R Tamiya brushed motors though 😍😍😍😍 Twinning 7 Quote Link to comment Share on other sites More sharing options...
totlxtc Posted May 17, 2023 Share Posted May 17, 2023 Really liking following your Tamiya builds @Kpowell911. I can feel the enthusiasm. Not touched any RC or gone anywhere in 3 weeks as had a big financial hit so its all home>work>home>work>home etc etc for me at the minute 😢 1 1 Quote Link to comment Share on other sites More sharing options...
Kpowell911 Posted May 17, 2023 Share Posted May 17, 2023 3 minutes ago, totlxtc said: Really liking following your Tamiya builds @Kpowell911. I can feel the enthusiasm. Not touched any RC or gone anywhere in 3 weeks as had a big financial hit so its all home>work>home>work>home etc etc for me at the minute 😢 Thanks for the kind words. Hope everythings ok with you mate. Im sure it will be. Remember these are just toys, if poo hit the fan, every single RC I own would be on eBay. It’ll sort itself out Im sure, keep your chin up! 1 Quote Link to comment Share on other sites More sharing options...
totlxtc Posted May 17, 2023 Share Posted May 17, 2023 Thanks man. Will sort itself out soon just got to graft a bit before i can go out and play. Got the Senton in bits with a broken servo and needing new tyres. (Seems the arrma is the money pit and not the xrays!) Broke arm and suspension pin on xb4 but have buckets of spares for that. Quote Link to comment Share on other sites More sharing options...
wolfie1 Posted May 17, 2023 Share Posted May 17, 2023 3 hours ago, Kpowell911 said: Had a few hours free this evening, Id like to say its cause I finished work early, but I did leave my house at 520am so Id hope so. All Tamiya love again (shock!) Oil shocks for the Humble TL-01. A servo for the SRX Full electrics for the R Tamiya brushed motors though 😍😍😍😍 Twinning Is it me or is the propshaft in that bottom pic thicker on the 1 on the left? Quote Link to comment Share on other sites More sharing options...
Kpowell911 Posted May 18, 2023 Share Posted May 18, 2023 7 hours ago, wolfie1 said: Is it me or is the propshaft in that bottom pic thicker on the 1 on the left? Think its just the lighting Quote Link to comment Share on other sites More sharing options...
ghazghul Posted May 18, 2023 Share Posted May 18, 2023 Decided random crawler build has spend long enough on the bench (may have been a veery long time), scrapped some plans that were never going to work, bodged a solution for the battery, stripped it down and did some painting. Quite looking forward to getting it built and to actually drive it. Hopefully that won't take me another 5 years... 2 Quote Link to comment Share on other sites More sharing options...
MrCake Posted May 20, 2023 Share Posted May 20, 2023 Really nice morning session with the old man to run some bashers and a couple of crawlers. Ground was nice and dry so just a bit of an air blow and brush and all will be good. 3 Quote Link to comment Share on other sites More sharing options...
Stormbringer Posted May 20, 2023 Share Posted May 20, 2023 Looked fun mate and i really like the wheels on that TRX4 Quote Link to comment Share on other sites More sharing options...
MrCake Posted May 20, 2023 Share Posted May 20, 2023 7 minutes ago, Stormbringer said: Looked fun mate and i really like the wheels on that TRX4 It was, 5 x cars in total and no breakages which is always a win. Especially with one of the cars being a FTX Outlaw! Thanks I wasnt too sure of them at first but wanted something a bit more scale looking. 1 Quote Link to comment Share on other sites More sharing options...
Stormbringer Posted May 20, 2023 Share Posted May 20, 2023 No breakages considering an FTX was involved nice 1 mate 2 Quote Link to comment Share on other sites More sharing options...
RC4WD fan Posted May 21, 2023 Share Posted May 21, 2023 Today was a good day 😁 fitted the new servo to the TRX4 and a receiver for the flysky GT5 took the stampede out so much fun now I’ve tightened the slipper and took the cragsman c for little trail walk don’t know why they more popular it’s up there with the TRX4 maybe a little bit better IMO 1 Quote Link to comment Share on other sites More sharing options...
Kpowell911 Posted May 21, 2023 Share Posted May 21, 2023 1 hour ago, RC4WD fan said: Today was a good day 😁 fitted the new servo to the TRX4 and a receiver for the flysky GT5 took the stampede out so much fun now I’ve tightened the slipper and took the cragsman c for little trail walk don’t know why they more popular it’s up there with the TRX4 maybe a little bit better IMO So glad youre enjoying the Stampede 🙂 1 Quote Link to comment Share on other sites More sharing options...
RC4WD fan Posted May 21, 2023 Share Posted May 21, 2023 22 minutes ago, Kpowell911 said: So glad youre enjoying the Stampede 🙂 I am very much so 👍 the motor does get very hot though on 3s from what I’ve read up the Velineon although can run 3s don’t really like it so will try on my 2s next time as see what happens I keep looking at this to replace it with this https://www.modelsport.co.uk/product/hobbywing-ezrun-combo-max10-sct-3660sl-3200kv-brushless-motor-420924 and sell the Velineon system 🤔 Quote Link to comment Share on other sites More sharing options...
Kpowell911 Posted May 21, 2023 Share Posted May 21, 2023 8 minutes ago, RC4WD fan said: I am very much so 👍 the motor does get very hot though on 3s from what I’ve read up the Velineon although can run 3s don’t really like it so will try on my 2s next time as see what happens I keep looking at this to replace it with this https://www.modelsport.co.uk/product/hobbywing-ezrun-combo-max10-sct-3660sl-3200kv-brushless-motor-420924 and sell the Velineon system 🤔 We run that in the Rustler, its bonkers Quote Link to comment Share on other sites More sharing options...
RC4WD fan Posted May 21, 2023 Share Posted May 21, 2023 5 minutes ago, Kpowell911 said: We run that in the Rustler, its bonkers So would you say it would be better for the stampede on 3s to run that combo? Quote Link to comment Share on other sites More sharing options...
Popular Post ghazghul Posted May 21, 2023 Popular Post Share Posted May 21, 2023 Put it back together, still needs the wiring sorted, which is going to be a squeeze. Many many mistakes were made, but overall quite happy. 5 Quote Link to comment Share on other sites More sharing options...
Popular Post Kpowell911 Posted May 21, 2023 Popular Post Share Posted May 21, 2023 Put some pointless bling on the SRX Got the Repsol Cossie sitting on the correct TA02 Chassis. 5 Quote Link to comment Share on other sites More sharing options...
Kpowell911 Posted May 22, 2023 Share Posted May 22, 2023 23 hours ago, RC4WD fan said: So would you say it would be better for the stampede on 3s to run that combo? You may disagree but I found the Stampede was more fun on 2S. In fact I dont think I ran it on 3S haha. But its a superior combo in every way 1 Quote Link to comment Share on other sites More sharing options...
RC4WD fan Posted May 22, 2023 Share Posted May 22, 2023 1 minute ago, Kpowell911 said: You may disagree but I found the Stampede was more fun on 2S. In fact I dont think I ran it on 3S haha. But its a superior combo in every way I’ve never run it on 2s so wouldn’t know I’m going to try it on 2s next time if I’m not happy with it I’ll buy the new combo 👍 that’s a good enough reason to buy new RC parts 🤣 Quote Link to comment Share on other sites More sharing options...
tanveer Posted May 22, 2023 Share Posted May 22, 2023 Built my tt02r today, quick maiden run on the driveway just to check it’s all good ready for Bedworth rc club this weekend. Entering the rookies class, first time at an on road rc club. 3 Quote Link to comment Share on other sites More sharing options...
Stormbringer Posted May 22, 2023 Share Posted May 22, 2023 Good luck and have fun 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.