jony nitro Posted November 30, 2012 Share Posted November 30, 2012 oh not good news. hope the seller sorts it out Quote Link to comment Share on other sites More sharing options...
RC4ever Posted November 30, 2012 Share Posted November 30, 2012 Is the motor ok for 10s ? Obviously the esc is yeah ? Quote Link to comment Share on other sites More sharing options...
samshirley001 Posted November 30, 2012 Author Share Posted November 30, 2012 (edited) the motor is rated at 11s ans esc at 16s Edited November 30, 2012 by samshirley001 Quote Link to comment Share on other sites More sharing options...
.AJ. Posted December 5, 2012 Share Posted December 5, 2012 Any come back on the esc yet mate?? Quote Link to comment Share on other sites More sharing options...
samshirley001 Posted December 5, 2012 Author Share Posted December 5, 2012 havent had the time to send it, but will today Quote Link to comment Share on other sites More sharing options...
Highlander Posted December 5, 2012 Share Posted December 5, 2012 (edited) i had a feeling this would happen 2. the 8mm bullets are really hard to remove, and one time i removed it and it removed itself from the wire. Not good if the bullet comes away from the wire, bad soldering. The 8mm's need to be squeezed gently on the ends to close the pins slightly, then they should fit in snug and pull out with a little bit of force. Edited December 5, 2012 by Highlander Quote Link to comment Share on other sites More sharing options...
samshirley001 Posted December 5, 2012 Author Share Posted December 5, 2012 (edited) like i said previously, its hard to solder when its very cold out. also, do you think a slipper would help prevent this from happening again? Edited December 5, 2012 by samshirley001 Quote Link to comment Share on other sites More sharing options...
norcoforever Posted December 5, 2012 Share Posted December 5, 2012 like i said previously, its hard to solder when its very cold out. also, do you think a slipper would help prevent this from happening again? considering your so far below the rated specs of the esc i would be considering that maybe its a general fault with the esc not your setup Quote Link to comment Share on other sites More sharing options...
samshirley001 Posted December 7, 2012 Author Share Posted December 7, 2012 I guess, seems as the proper baja flux has no slipper (what i'l still a bit surprised about) sent the ESC off now, Quote Link to comment Share on other sites More sharing options...
samshirley001 Posted December 9, 2012 Author Share Posted December 9, 2012 the seller got my esc, apparently i blew 4 mosfets and a phase. oops Quote Link to comment Share on other sites More sharing options...
.AJ. Posted December 9, 2012 Share Posted December 9, 2012 But will they warranty it??? Quote Link to comment Share on other sites More sharing options...
samshirley001 Posted December 9, 2012 Author Share Posted December 9, 2012 they have, should be here on tue Quote Link to comment Share on other sites More sharing options...
norcoforever Posted December 12, 2012 Share Posted December 12, 2012 any news on this one buddy? Quote Link to comment Share on other sites More sharing options...
rc rookie Posted December 12, 2012 Share Posted December 12, 2012 following Quote Link to comment Share on other sites More sharing options...
samshirley001 Posted December 12, 2012 Author Share Posted December 12, 2012 no news yet, will update when something arrives. i have been waiting for a few days for the speedo to arrived. tried an old dying castle mamba max on 5s with it, and it killed that esc Quote Link to comment Share on other sites More sharing options...
Highlander Posted December 13, 2012 Share Posted December 13, 2012 Mamba max Quote Link to comment Share on other sites More sharing options...
Revorocks Posted December 13, 2012 Share Posted December 13, 2012 no news yet, will update when something arrives. i have been waiting for a few days for the speedo to arrived. tried an old dying castle mamba max on 5s with it, and it killed that esc A mamba max, really? Wouldn't even run a 1/8 with that, let alone a 1/5 What were you expecting Quote Link to comment Share on other sites More sharing options...
.AJ. Posted December 13, 2012 Share Posted December 13, 2012 what a waste Quote Link to comment Share on other sites More sharing options...
samshirley001 Posted December 13, 2012 Author Share Posted December 13, 2012 i ment mamba monster still killed it Quote Link to comment Share on other sites More sharing options...
rc rookie Posted December 13, 2012 Share Posted December 13, 2012 when you getting your new esc ? Quote Link to comment Share on other sites More sharing options...
samshirley001 Posted December 13, 2012 Author Share Posted December 13, 2012 erm it arrived like 10 mins ago gonna solder it up tomorrow, as i don't have work till 5pm! Quote Link to comment Share on other sites More sharing options...
rc rookie Posted December 13, 2012 Share Posted December 13, 2012 sweet Quote Link to comment Share on other sites More sharing options...
samshirley001 Posted December 14, 2012 Author Share Posted December 14, 2012 fitted the replacement ESC, but now a new problem. cogging, really bad. the transmission runs okay, batteries are fine, tried messing with the transmitter, checking motor wires, all seem fine. when i hold he rear up, it cogs, then gets going again, but on the ground, it barely moves Quote Link to comment Share on other sites More sharing options...
Highlander Posted December 14, 2012 Share Posted December 14, 2012 you blew the Mamba monster because the motor uses far more Amps than it can supply... Quote Link to comment Share on other sites More sharing options...
norcoforever Posted December 17, 2012 Share Posted December 17, 2012 anymore updates? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.