Oh How Original Posted April 20, 2015 Share Posted April 20, 2015 I doubt it's faulty Savox servos, especially when it's happening to both of you. Although it is rather strange. I know Spektrum gear can have bad signal issues if the rx antenna is below the coil (apparently this is the reason) so it might be worth holding the RX as high as possible, just for a simple test to see what happens? I know it's obviously not practical to use but it might eliminate/promote a certain problem. Quote Link to comment Share on other sites More sharing options...
patriots-1 Posted April 20, 2015 Share Posted April 20, 2015 HiIm not using spektrum gear ??cheers sean Quote Link to comment Share on other sites More sharing options...
Oh How Original Posted April 20, 2015 Share Posted April 20, 2015 I know you're not, you said you're using Futaba. But the fact remains that if SOME 2.4Ghz radios can have issues, then others might, depending on the receiver of choice? Never had any issues at all on any RC's with my Flysky lol, cheapo FTW Quote Link to comment Share on other sites More sharing options...
patriots-1 Posted April 20, 2015 Share Posted April 20, 2015 The thing i cant understand is both my radios work faultless in my baja's Quote Link to comment Share on other sites More sharing options...
Oh How Original Posted April 20, 2015 Share Posted April 20, 2015 Different engine, different coil, possibly different killswitches? Quote Link to comment Share on other sites More sharing options...
Scoobie007 Posted April 20, 2015 Share Posted April 20, 2015 Probably silly mentioning it, but is the plug functioning properly? Doesnt the cmr7h have a resistor or something to stop electrical interference, dont troll me, just a suggestion lol Quote Link to comment Share on other sites More sharing options...
andyknight Posted April 20, 2015 Share Posted April 20, 2015 i believe the cmr7h does have a resistor but that doesn't stop it from going bad over time. Might be worth replacing the plug, cheap test anyway. Quote Link to comment Share on other sites More sharing options...
almighty15 Posted April 21, 2015 Share Posted April 21, 2015 My Spektrum did this and it was because the servo's I was using were analog, changed to digital and problem went away. Quote Link to comment Share on other sites More sharing options...
kkppww91 Posted April 26, 2015 Author Share Posted April 26, 2015 Found my standard steering servo out yesterday and tested it in my rx to see if it worked fine. Turns out that does the exact same as my savox. I'm guessing it will be my futaba rx after all Quote Link to comment Share on other sites More sharing options...
kkppww91 Posted April 26, 2015 Author Share Posted April 26, 2015 My bartolone so pipe is in need of a refurb. Was wondering if I could sand or wire brush all the black paint off and go for a polished look. I have a dremel and all the polishing gear. Is there any threads on how to do it? Quote Link to comment Share on other sites More sharing options...
almighty15 Posted April 26, 2015 Share Posted April 26, 2015 Just search for a local company that do chemical stripping. That's what I've done in the past, perfect results and much better then a wire brush. 1 Quote Link to comment Share on other sites More sharing options...
kkppww91 Posted April 26, 2015 Author Share Posted April 26, 2015 Can they bring them to polished finish aswell? Quote Link to comment Share on other sites More sharing options...
kkppww91 Posted April 27, 2015 Author Share Posted April 27, 2015 Wire brushed exhaust today with my dremel. Can anyone recommend some paint for it? Quote Link to comment Share on other sites More sharing options...
flatout! Posted April 27, 2015 Share Posted April 27, 2015 You'll need a high heat paint pal, and make sure you De grease it before you paint it to Quote Link to comment Share on other sites More sharing options...
kkppww91 Posted April 28, 2015 Author Share Posted April 28, 2015 Oh and a question about gearing aswell. I'm running the pro mx g340 with a Bart xp pipe. Still on standard gearing and diff oil. Any one recommend what I should change to? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.