Jump to content

steephill

Members
  • Posts

    261
  • Joined

  • Last visited

  • Days Won

    2

Everything posted by steephill

  1. Looked a grand day out ๐Ÿ‘. Nice spot over at Rivington.
  2. George, Sasha (Aunty Lou) and Kaysha. Sadly don't have these three. Had them from puppies right till the end. Ralph, he's nearly five years old. One of the friendliest dogs you could meet, he loves everything. Bella, Rottweiler labrador Cross. She's a bit crackers but a good dog. Ralph with his mate Trevor. One of my bunnies.
  3. I've been looking but can only find the BD chassis in the picture above. They are 159 euros and I've no idea if they are any good. They look nice, but that doesn't mean anything. I'm having a go a building a lcg or as capable as I can get it truck. I'll have a look at the gspeed as I haven't seen those.
  4. Does anyone know where I can get carbon chassis rails for an scx10?
  5. Top of the list! No1! That's brilliant mate๐Ÿ‘ I suspect you have more to come from your infraction. Shame about the damage.
  6. Not too far for me. I'm up for that๐Ÿ‘
  7. Welcome to the forum mate ๐Ÿ‘. Love my hyper 7 ๐Ÿ‘
  8. Welcome to the forum mate ๐Ÿ‘
  9. Hiya mate can I get the 3650 6900kv motor please?
  10. The batteries are nothing special. Overlander sport track 4500mah 55c burst. I'm going to try and pick up some higher discharge 3 and 4 cell batteries.
  11. Thanks mate๐Ÿ‘ Yeah 3s. Found the video!๐Ÿ‘ Not played with the turbo settings yet. I turned the punch down to start with just to help smooth power delivery. I'm gonna have a look at the settings soon. I'm pretty sure that setup has a few more mph in it. I thought I had smoothly got on to near enough full throttle on one run and it spun the wheels. Lots of top end power I want your 60mm can now ๐Ÿ˜‰
  12. Did a few more runs with the vantage tonight. Changed the motor for another Xerun, 3656sd 4000kv. Quite a bit more top end power than the 3400kv I tried last time. Even brought my gopro to film it. A new pb of 66 mph. I was really chuffed until I got home. The bloody gopro didn't record any videos! ๐Ÿคฌ It was on video mode and flashing red. I'll go through the settings format the card etc and try again. Was chuffed to see the numbers but ripping no videos.
  13. That's the other location I mentioned, Carrs Industrial estate, Commerce St. Should be pretty quiet in the evenings ๐Ÿ‘
  14. That would be grand mate ๐Ÿ‘ I'll be back out next week.
  15. I'm really enjoying the speed runs, it's good fun. I've got another potential spot on carrs industrial estate.
  16. Yeah mate, Fearns moss. You really have to pick your time carefully as it can be quite busy. I got a good few runs tonight from just after 7pm
  17. Did a few more speed runs this evening. The 124019 did 63mph. A little improvement but motor change needed. And I gave the ftx vantage it's first speed run, managed 59mph. Not too bad for first go. Ran a xerun 3656sd motor 3300kv on 3s. Big thanks to @Redback for helping with the gearing๐Ÿ‘ Got a few different motors to try, so hopefully the next run, bigger numbers.
  18. I've got one brand new with shafts. You can make me an offer.
  19. I've run various soft case lipos in my crawlers without any problems for a good few years. I've properly drowned most of my crawlers.
  20. Anyone know if there is an aluminium chassis for the vantage? I've seen them for the carnage but not vantage.
  21. Managed to do my first speed run. Took the rustler 2wd fairly stock, xerun 3656sd 4000kv. 3s lipo. Controlling wheelies is fun, until it went skating down the tarmac on it's roof๐Ÿ˜‚. Got 57 mph out the rustler. I may try a few changes and see how that goes. Also tried a Wltoys 124019. Quite a lot easier to control than the rustler. Stock gearing, rocket 3650 3900kv motor xerun 120 amp esc 3s lipo. And got 61 mph. Didn't destroy anything and learnt a bit so not a bad do.
ร—
ร—
  • Create New...