David Lucas

bump

Bump

Hi everybody I am selling my new Axial Ryft kit as its not my cup of tea. This was the kit version that I've built and only used twice now. It's as good as new except for some very light scrapes on the frame, and I replaced one of the front lower left link rod end with a generic Axial one as one broke off straight away. I will include the Savox 0231 MG steering servo, (this is NOT new) The kit includes the 2 speed transmission gears (that i didn't fit) also installed is a castle mamba X esc and can. This is the 1410 3800kv combo https://www.castlecreations.com/en/mamba-x-1/mamba-x-sct-sensored-25-2v-wp-esc-and-1410-3800kv-combo-010-0161-00 Im looking for £300 + postage - for the Ryft + servo WITHOUT Castle Mamba X combo or £470 + postage WITH the Castle Mama X combo not looking to sell just the castle kit separately though as i might re purpose it for another vehicle. any questions please shout - PM me on here thanks David

The purple arrowmax ones are very good

It comes with 38t plastic spur and 17t pinion / 3mm shaft as standard. I went with the optional 45t on a 12t pinion myself. See attached pic for gearing chart. Sent from my BLA-L09 using Tapatalk

I just built this one. it's a really well thought out and good quality kit, can't wait to get it dirty! Sent from my BLA-L09 using Tapatalk

Greens models did one with trx-4 mounts for 313mm wheelbase that should fit. Or try jsscale in France or club5racing from eBay.. Sent from my BLA-L09 using Tapatalk

Thanks Stimpy I'll take another look at the set up and get some more pics. I have other shocks but hoping to use these king ones for this, limiting them to 90mm or so shouldn't be a problem, is that best done by way of a spacer inside the shock or a limiting strap of some description. Cheers! Sent from my BLA-L09 using Tapatalk

Hi all, I've been re inventing my scx10.2 with a new look. I've decided to go back to CMS, It's set up for droop and ive tried to keep the panhard as close as possible to parallel with the drag link. However its got a fair bit of bump steer and also the axle shifts off to the side quite a bit between suspension top and bottom positions! Any tips / best practice that would help minimise these? Toying with the idea of fitting sway bars to stop body roll or do you think heavier weight oil would be a better first port of call? have 30w in at the mo but they are quite long 110mm any advice appreciated! Also what do you think of the urban look? I found some Electro -luminescent wire on Amazon to use as rock lighting but thinking it might look cooler as a neon style sign in the rear window. It runs off a 12v invertor in the little electronics box at the back, wired via the receiver to channel 3 [emoji846] Sent from my BLA-L09 using Tapatalk

What's the wheelbase, please? Sent from my BLA-L09 using Tapatalk

You should've told me this last week! [emoji23] Sent from my BLA-L09 using Tapatalk

hey. I got an HPI Venture recently that has been a really good performer out of the box. Just needed some better tyres. It's got good potential for scale body swaps with the motor at the front and lots of space for interiors.. There's 3 different options for colours and they are all around £300 mark. One downside is that it's on 48DP fixed size spur so limited options for gearing changes. but it's very well balanced and nice and quiet, comes with 3 channel RX and it's fully waterproof too. Sent from my BLA-L09 using Tapatalk

Hi, Would you consider £380 + postage Mr Gaz? Sent from my BLA-L09 using Tapatalk

Go on then I'll buy it! Sent from my BLA-L09 using Tapatalk

I need that in my life Sent from my BLA-L09 using Tapatalk