dazzzer

I was looking into the UK laws on Drones under 250g weight from what i have read the only reason you need an operator ID for the likes of the dji mini is because it has a camera on it, I am not sure why a camera on a drone under 250g would make this difference? but while most drones under 250g will probably have a cheap camera of some sort and are still be classed as more of a toy drone. Although i am not against any new rules needed for safety I just find this to be about trying to make money rather than safety, I think the rules are crazy when you get to the under 250g drone class , when you consider most are just cheap toys with a really cheap camera but you will still need the operator ID as the laws state ,

I ordered Eachine E58 WIFI FPV with two batts for £40 , should be here in a few days seems ok for the price

Atti mode is challenging more so if you where really high up and with wind, could be a challenge for someone with experience in flying too , I would get a cheap drone to learn to fly on first , one of my friends told me about his gps went off and entered to Atti mode, he had some experience in flying but was took by surprise he couldn't control it , he said there was some wind but he had it out in the dark which probably wasn't a good idea ,

I never fly that high up because there so small and hard to see so I really wouldn't see the point in joining , I use to fly bigger RC planes years ago and I don't think they was laws back then or I just didn't know about them, now I enjoy the micro class rc plans and drones mostly indoors and sometimes outside if its not to windy , I think all these laws are just silly and complicated, as long as I can go my local park and not be breaking any laws I will always make sure I am under 250g.

Do you know if the weight of the drone is included with the battery on ?

I just want to know more about the RC flying laws in the UK, and if it all applies to me? I mostly fly micro rc normally fly in doors but sometimes I take them to the local park on nice days , I think my biggest drone is 230grams in weight , I am just wondering if these are in the same class of law as the bigger ones , Also heard they was new laws coming in for a test and licence to fly but really would feel silly if I had to take a test to fly micro planes and drones round the park .

I am doing my first build with a TT02 and I am building it with the high ground clearance settings front and rear , My question is about the stock shocks and springs , the front shocks seem to be more loose fitting , If I hold it with two fingers I can get side to side movement and spring can more round the shock , the rear shocks and springs are more tight the springs are more compressed with little movement , I have used the following holes to slot the shocks and there are know wheels on yet and I am Just wondering if this is normal or have I done something wrong?

yep the battery is around 20c to 30c 5000mah I noticed the connectors on the battery the connectors are HXT4mm , would I be ok to change them to xt60 connectors without a drop in power ?

Can anyone tell me how to workout the amp draw so I can pick what battery connectors and wire I should get for my RC car ? The battery will be 2s / 5000mah , Motor specs are (KV: 2189kv Max Current: 33 amps .Max Power: 245 watts .Idle Current: 2A . Weight: 170g , I have a 80a esc .

I am doing a brushless build for a short rally track I don't want a big increase in speed and I am just wondering if this motor will work? and can I still use the stock pinon on it ? TrackStar 17.5T "Outlaw" Sensored Brushless specs KV: 2189kv Max Current: 33 amps Max Power: 245 watts Idle Current: 2A Shaft: 3.17mm Weight: 170g Cell Count: 1~2S Lipoly

I am doing my first build TT02 and would like to know If it is ok to fill the stock "friction shock with grease ? I have heard that some people do this but it is not in the manual

thanks mate ! yer not had much look with the stock pull start it seems some how the cord has melted .

Just wondering if any one knows the dia of the cord need to fit the stock pull start ? Been looking at this on ebay but really need to know the dia so it will fit in to the pull start with out any problems - http://cgi.ebay.co.uk/NEW-SUPER-STRENGTH-Pull-Start-Cord-Nitro-Engines-/160561701760?_trksid=p3286.m7&_trkparms=algo%3DLVI%26itu%3DUCI%26otn%3D3%26po%3DLVI%26ps%3D63%26clkid%3D1343006926385010319

I was driving my buggy a few weeks back not tried it since but i remember it cut out on my and i lost the cord to the pull start , when i went over i noticed the glow plug had gone it must have shot out of the engine as i remember it was in good not to tight but tight enough , just wondering why it happened and do i just need to get a new glow plug .