Perko

Yes I have, followed these instructions: Clicky. Works great!! I'm not the best solderer in the world or have an indepth knowledge of electronics, but mines been going strong for 6 months. Give it a try!

I use the Fusion smart guard to check capacity of lipo's works pretty well, gives a percentge left rather than actual mAh: http://store.modelpower.co.uk/fusion-smart...ecker-103-p.asp

Thanks very much for this, my charger only goes to 5A and they are 5000mAh batts, so have borrowed a charger which goes to 6A so will give it a go at charging at 6A. You're right about being your fav truck - it's insane - can't imagine what it's like using 6s cells!! Cheers mate, will report back!

Grateful for some views please? I bought two second hand 7.4v Nosram vtec Extreme Power Lipos from ebay They said they had only 20 cycles through them and were always balance charged. When I had them, I checked their capacity using a fusion smart guard and they were both at 86 percent. So I thought I'd top them up before using them in my ERBE. The one went up to about 90 prcent but the other one refused to go above 86 percent on my charger (Core UDC20). So I tried them in my ERBE and there was just no punch at all and was going about a 1/4 of the speed (at the most). I wasn't happy and thought I'd try one of my normal sets of batts to check all was ok with the truck. Using my 7.4v Trakpower's it it was back to what I'd expect - Wheelies and full speed!! Anyone any ideas what may be up with the Lipo's? Thanks.

Yep, I have one and it fits underneath the wing.

Right, time for an update on this. Despite initial reservations from Hobbytoys88 on taking responsibility for sorting out my smoked ESC, they tried to say I should have used a bigger fan!?! I pointed out that in 10 metres, it couldn't have been fan that was the problem and I was only using 6 cell NiMhs. I also poined out that Hobbywing recommend only changing to a 12v fan for 7 cell or 3s Lipos. As a result, they said they would look at reparing it (not replacing it), so just a heads up, they say the EZRun systems don't have any kind of warranty when supplied by Hobbytoys88. In terms of cost, I had to pay for the postage to send it back to China (

Thanks Gary, will be using a 19t in touring car for racing, and a 10T eZrun for bashing. Better off getting the Overlander's for bashing and the FX Voltz for racing? Cheers. http://www.modelsport.co.uk/index.php?Call...mp;ItemID=31001

I know there are some recent topics on the EZrun, but thought I'd share a recent experience with others who are considering purchasing the brushless system. Ordered 3 x eZrun systems for each of my cars. Went for the 10T 35A versions and ordered them from Hobbytoys88 from ebay. First off, very impressed with the delivery, they arrived in 6 days from Hong Kong. Tried out the first one in my TT-01. It went for about 5 seconds, then stopped, luckily had the shell off as smoke started bellowing out of the ESC, so thought that didn't look good and switched it off straight away. I touched the battery (a 3700mAh GP NiMH pack) and I couldn't even keep my finger on it for a second it was absolutely red hot. Unfortunately the eZrun system is completely dead. Does anyone have any ideas what could have gone wrong? Faulty ESC, problem with the battery? Am pleased to report, that the other 2 eZruns are perfect and am very pleased with them. Athough I haven't used that 3700 pack with them!! I have emailed Hobbytoys, asking for a replacement, I'll post up my customer aftersales service experience if I get a response. Any thoughts appreciated. Cheers.

That's great, thanks for such a quick response Adam! Will treat myself to a couple. Cheers.

I wonder if someone could advise if these are any good for club racing? http://www.modelsport.co.uk/index.php?Call...mp;ItemID=31516 Cheers.

Thanks very much again Garry for your advice!

Hi, can someone please advise if this Tamiya pinion set (http://www.modelsport.co.uk/index.php?CallFunction=BasicSearch&TextString=50357) will fit in the B4 please? Cheers.

Hi, I'm pretty sure it's around 14,500rpm.

Hi, grateful for some advice re the above ESC please? Been bashing with my new TT-01 which I've had for a couple of weeks today. I bought it wihout an ESC so I could fit the Viper. I also insalled a 17x2 Turn LSP Fusion 3 motor and am running with a 58 spur and 22 pinion gearing setup. It's been great, but suddenly today, I slammed the brakes on, then I had no response from the throttle. As the steering sevo was working I thought the ESC had just shut itself down to cool down. Upon feeling the heatsink on the motor it wasn't that hot at all. I left it for five mins and hoped it would start again. I waited with aniticipation and Hooray it did! But now the ESC won't engage reverse, it brakes but no reverse. I re-did the setup process for the viper, just to check that the ESC's reverse didn't go into disabled mode for some reason. But it's definately in .5 seconds delay before reverse mode with 60% braking. Any ideas anyone please? Thanks!

Thanks 53HRA, adjusted it as you said, now runs perfectly straight at max speed. Thanks very much for the advice!!!!