Leslie

Steering is a bit jerky but it seems to have righted it's self again I think it's definitely the radio, I've been looking at some of the dumbo rc controller's as I want 1 controller for about 4 different cars is this possible

Hi this monster truck is causing me lots of problems, OK this I think is a radio problem I have changed the motor to a lower kv new pinion and gear, it's also had a new rear gear box for previous problem. So the motor is jerking when I try going a low revs some times it's OK and sometimes not other other times no response from the remote at all , the battery is fine a 5200mah 50c lipo. So I have included a video to see what members think it maybe, plus the remote has been binded Thanx for looking received_1080001903297142.mp4

It's OK now and everything is work as it should Thanx

Hi if I get another motor with a lower kv, would the 60a esc i have already be OK for it

Hi there well the buggy is working as it should now, it was the rear diff put in the wrong way, I would not have sorted without all the replies Thank you

Thanx for the swift reply I will check this shortly it doesn't look like the rear or front is upside down maybe something in side.????

Hi not a daft question, I have just checked this and the back wheels are going forward and the front wheels are going in reverse, so when I got this it must have had something done to the rear diff I'm guessing now. I have asked guy who I got it off, was anything done to the rear diff, he said he isn't sure as someone looked at it for him. So how do I go about sorting this Thanx for the not so stupid question

Hi today I took the drive shaft off and tried the buggy and everything working OK except no front wheel drive and no juddering, as soon as soon as I put the drive shaft back in it goes back to wheels locked and the buggy juddering. I have checked the front and rear diff they are turning as they should. So do you think I it still maybe the motor I do have a motor to go in just got to find a battery different connector

The motor is a king Kong 3650 brushless 4500kv plus a 60A esc, and the battery is a lipo 7.4v 5200Ah 50c

I have just changed the pinion and spur as I thought it was that, but still the same. The pinion and spur was changed like for like 17T / 64T

Hi there I've not long been given a HiSpeed 1/10 monster truck with brushless motor, and the problem is I hold the buggy off the ground and accelerate the wheels go round no problem. But when I put it on the ground it just judders and doesn't move, I have checked most things drive cups etc all tight any ideas ,???? Motor maybe

Been a long time since I posted this thread about wheels not spinning. The thing is when I changed the pull start for a roto start I put back the one way bearing the wrong way so when I was starting the engine it started backwards and that was the problem. So now the engine starts the right way and now the wheels are turning correctly. Sorry to be a pain but the way I solved it was by back tracking what I had done then realising what I had done 🙄

To what I can see I can't see a slipper clutch just a 2 speed drive clutch are they the same thing I'm not sure see pic

Hi I have checked the bell housing while running the engine at high revs and the clutch is engaging, so I don't think its the clutch. I have also checked all the shafts couplers and all seem to be tight and working as they should. Also I have read about slipper clutches is this just electric motors or does it apply to nitro engines as well????

Hi I have checked the flywheel that turns the engine over and the bell houseing is spinning, also I had a close look at the flywheel and there is tiny drilled hole in it, should there be a grub screw in it???

Hi there this my first post a newbie I recently brought a himoto syclone from new, and when I start it on tick over its OK, but when I rev up the engine the wheels are not turning I have checked all the gears nothing sheared. When I turn the wheels manually everything is turning as it should. So I am thinking the clutch not engaging, so could the clutch break or whatever as the engine only been started about three times not even run in yet any ideas Thanx for looking