Jump to content
MSUKForum is a participant in the eBay Partner Network (EPN). When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Read more >

Rcjim11

Members
 View Profile  See their activity

  • Posts

    61

  • Joined

  • Last visited

 Content Type 

Everything posted by Rcjim11

  1. Rcjim11
    Ok thanks, what diameter are stock self tappers? How did you mod the gearbox lip? cheers
  2. Rcjim11
    Just did the diff oil in front and rear, and when reassembling managed to strip the screws that secure the front assy to the chassis. The screws seem to have made a new thread - fracturing the inside of the diff case! Where can these screws be obtained? Cheers Jim
  3. Rcjim11
    I'm currently sorting out the differentials in my truggy flux... What is the best method of cleaning grease off? Cheers Jim
  4. Rcjim11
    Hi, Where do the droop screws locate? Cheers
  5. Rcjim11
    Probs the Hobbywing one from GS
  6. Rcjim11
    You can change the lvc and other cool brake thingies with the nifty little program card that md69 recommends!
  7. Rcjim11
    You can make or buy a conversion piece from deans to 4mm bullet red connectors. I use 2x2s 45C and 65C. I can't tell the difference between those two But it may be a different story comparing 20C and 45C.
  8. Rcjim11
    Great Thanks!
  9. Rcjim11
    So, what parameters does it have for setting up the brake?
  10. Rcjim11
  11. Rcjim11
    My flux has an extremely hard brake, (ie. from half to dead stop with the slightest touch of the brake) is this what the esc is preset as from the factory? Without releasing the button, it goes straight from braking to reverse... is this right also? Help much appreciated! Cheers Jim
  12. Rcjim11
  13. Rcjim11
    The Led light that is supposed to flash when programming the esc in the manual. Just making it clearer! Thanks again Jim
  14. Rcjim11
    I just tried plugging in the battery to the car and no led lights were present. Where do they originate from please??????? Cheers
  15. Rcjim11
    Gear mesh need setting up? Cheers
  16. Rcjim11
    Is it only the wheel nuts that come pre-unloosened from the factory ready to fall off or are there other things that need setting up?! Also, does the gear mesh need doing? Cheers
  17. Rcjim11
    Oh, so that's what the plastic things are! Thanks
  18. Rcjim11
    How does one increase the ground clearance at the front end, mine seems to be hanging low at the front? Cheers
  19. Rcjim11
    Currently, i have 3300mah 2s in 45/65c x4 and 1 3200mah 4s 30c. I know the 2cells are fine for constant/burst.. Not so sure on the 4s pack. How long will they last approx? Cheers
  20. Rcjim11
    So does that mean I need lipos to handle the burst or just the constant? I assume constant but j/checking!
  21. Rcjim11
    Does any1 know the rating of the esc in the flux? Just wanting to know whether my lipos are up to the job. Cheers
  22. Rcjim11
    Btw, does the manual tell you how much to put in? Cheers
  23. Rcjim11
    Thanks, will get some to play with
  24. Rcjim11
    Ok, great. Is that the ansmann stuff ms sells?
  25. Rcjim11
    I now understand that different weights of diff oil can be applied, so is there a good combo Links please! Cheers Jim
×
×
  • Create New...