brushlesswesty

Niceeeeeee

Hi mate rebind the motor ?

I can only advise what is as told to try mate, but yes dodgy cells in your lipos could be a cause ! Also was advised to get an extronix power cap , only a few quid so worth getting one anyone Let me know how you get im happy to help ! What model have you got?

Mmm....that would be pretty bad luck to be 2 escs ! But u never know?! Did you replace it with a new or second hand one? Have you tried using someone else's lipos ? I feel your pain!

Yes finally !! It was a faulty esc !!! Thanks all and hope it helps you electro like !!!

Will do buddy cheers!

Nice one buddy Will that hobbywing make any difference to power or anything? Cheers

Cheers Pete Will Look at this, I gues I could lower it just to see if it gets more run time at normal speeds Yes Pete steering always works

Nice one tug thanks for all the help ! Will lower the lvc see if that makes a difference sounds like a start to see if it eliminates it! If not I might just go for that new esc ! Will that make any difference to power with stock motor?

Hi tug Small pinion is 15t, spur is 50t Motor & esc , standard , 1965 motor , 80amp esc Not sure what pit card is ! But set to - Drag brake force 0% Lipo cut off 3.2v Start mode punch - L5 Max brake force 25% Neutral range 9% Motor timing 15.00 If I push fairly hard it runs smooth enough but when pushed very slow it's quite notchy if that's normal?

Ok mate cheers will get one anyway!!

Hi toxic Battery's are Hpi plazma 5300 7.4 30c ? I bought it second hand , now wishing I bought a brand new one! But it's had minimal use and superb condition . Maybe I should check the gearing , will have a look at that, I'm guessing your saying that the gearing if changed is putting strain on the esc ? New to electric !!

Nice evss Will get one, could this be the power loss issue aswell do you U think?

Hi toxic Nope all original ! Really not sure what it is , sounds like something simple but , maybe overheating esc? Faulty ? Interested in the power cap do have a link?

Hi guys So Hpi trophy truggy , Thought battery's were causing the problem but both balancing at 4.20 a cell , take car out works fine for 2 mins then loses power goes roughly half speed. Then random total non response last couple of seconds, take battery's out there still balancing at 4.04ish per cell. Leave it for minute then power comes back and loses 20 seconds again! What do we think?! I'm stuck!

Great video .... That's so easy doh ! Cheers guys !

Hi guys Would like to balance charge plazma 5300mah 7.4v 2s with the over lander I persume its the White plug on the battery? Have looked through the manual and slightly confused! Any simple answer would be appreciated! Cheers

Nice one nitro ! Think I might just invest in the 5000 for now at that price!! Last thing I need deans connection , noticed they are not?

Woo not sure what happened there lol!

Cheers moorby So in regards to the 30c should I be getting 30c spec to replace ? If it's lees or more than 30c what will the difference be? Cheers again Cheers moorby So in regards to the 30c should I be getting 30c spec to replace ? If it's lees or more than 30c what will the difference be? Cheers again Cheers moorby So in regards to the 30c should I be getting 30c spec to replace ? If it's lees or more than 30c what will the difference be? Cheers again

Sounds like where I should be looking! So electric is new to me , So is the plazma I have a 3s? And what will 6600 give me a 5300 won't? Sorry if that sounds silly probably does! And what does the 30c 20c all stand for? Appreciate it guys!

Hi guys I've currently got Hpi plazma 5300 7.4 30c x2 Looking to get another 2 any suggestions of same spec but slightly cheaper versions? Cheers !

Ok so I've just taken the lipos out plasma 7.4v 5300 x2 there is very slight swelling ie the sides have a slight swell at most a mm at a guess , there not dead sqaure or flat as it were , is this ok?