lee williams
-
Posts
23 -
Joined
-
Last visited
Content Type
Profiles
Forums
Prizes
MSUK-Forum - RC Model News and Community
Articles
Events
Everything posted by lee williams
-
Ok then thanks for that mate think al just go buy one lol
-
Hi all just wounded if its possible to convert. A on road. To off road i have a hyper 10 4wheel drive on road
-
I have a hyper 10 with a force 15 engine i have noticed. That it don't have a lsn on the throttle. Side Sent from my RM-914_eu_euro1_280 using Tapatalk
-
I have tryed it just cant seem to get it rite i get it to idle fine then when a open it up full throttle. It cuts out t So a start doing the hsn then it sends the idle off slightly lol Sent from my RM-914_eu_euro1_280 using Tapatalk
-
Hi is a one that can help me out that i can go to or thay can come to me and help me tune my car i just cant master it im in Warrington Sent from my RM-914_eu_euro1_280 using Tapatalk
-
Al take a vid and post to to show from starting up to it opening up. Then cutting out Sent from my RM-914_eu_euro1_280 using Tapatalk
-
Lee -hyper 10 warrington Sent from my RM-914_eu_euro1_280 using Tapatalk
-
Its been set to factory setting but had to open hsn a bit to keep it running but its ok opening it up but soon as fully open it just cuts out cant be the glow plug as had new one in today Sent from my RM-914_eu_euro1_280 using Tapatalk
-
Hi all can anyone help i have a hyper 10 with a force 15 engine. Im having a bit of a problem with. When its running and i open it up full it cuts out not sure why can someone. Help me out with what to do pls Sent from my RM-914_eu_euro1_280 using Tapatalk
-
Well by this time tomorrow. I should have my 1:10 hyper 10 up and running from the dead fingers crossed Sent from my RM-914_eu_euro1_280 using Tapatalk
-
Hi im looking for a hyper 10 Central breaking system or the pads to replace. The ones on my hyper can anyone point me in the rite place to look cant see anything on tbay Thanks in advance
-
Thanks oodboo
-
Hi im looking for some where I can get the little mounting clips for a servo like the ones in the pic
-
Like me then all looks good on the car just the ll Elc what did u use to clean it i have some degreaser. A was g a use but don't no if be safe Sent from my RM-914_eu_euro1_280 using Tapatalk
-
A can turn the nut where the pullstart is and see the piston go up and down and hear a pop sound when do it so don't think its seized. Up Sent from my RM-914_eu_euro1_280 using Tapatalk
-
Lol go ask him for it and the belts seem in good condition. Pretty tight to have orded a new air filter for it just hope it starts up when all sorted out Sent from my RM-914_eu_euro1_280 using Tapatalk
-
I have found that blacksmiths do the one that is for my model a think my engine is a force 15 nitro engine is has the sam mark on the engine block
-
http://i1282.photobucket.com/albums/a524/lee_williams3/WP_20140710_17_33_44_Smart_zpsc152d8ee.jpg
-
Ok then well got my car today needs servos a wheel nut and pull start I was looking at the engine and can see a number 15 on it dont no if that will help me with the pullstart will put some pics on now some how
-
ok then al try post a pic of what I got thanks for the lonk just ordered it lol if worse comes to worst al just have to take it back to the basic and fill it with new gear
-
Where is the 3 sisters track ?
-
Nice to hear that a dont have a budget just willing to to pay for the bits that I need to bring it back to life got it at a bargain at
-
Hi all am new to all this I have just got a hyper 10 off ebay for a project with my lads its missing some bits like tires pullstart and a servo My 1st question is do the servos have to be the same or am I best to just buy a new set and receiver