mchaggis
-
Posts
15 -
Joined
-
Last visited
Content Type
Profiles
Forums
Prizes
MSUK-Forum - RC Model News and Community
Articles
Events
Posts posted by mchaggis
-
-
Update
Bought a clutch tool , fitted clutch no probe with tool works a treat
Cheeers all for ya advice
Mchaggis
-
Managed to take off flywheel mullgrips n 10mm ring spanner , mmm I thinks the nut that holds on the flywheel
Was'nt tightened up enough and hard to remove as had thread lock blue on , anyway took off flywheel replaced and tightened
Up refitted clutch pic below refit few days as on night shift
Thank to all
Mchaggis
-
-
Thanks guys
I don't think the flywheel tool would work as flywheel fitted is loose and spins , was all
Fitted as per diagram now can't undo nut in front I'll try post pic
Cheers mchaggis
-
Thanks for your replies ,
Just removed engine and found the flywheel had come loose , so hopefully when the piston locker gets delivered
I'll remove the flywheel and replace thread lock it , as far as I know the clutch shoes fitted OK however the springs I'm not
Sure of as the long bit of spring rubs on inside of bell housing is this right ? Its something I have never had to do or change
Till now ,
Before removing engine tho I moved it away from spur gear and run a full tank through the engine 1st tank run in
And noticed that the bellhousing was still spinning,
Is there a video or pics of clutch springs being fitted in the propper way ?
Thank you all great full and appreciate your help
Cheers mchaggis
-
Anyone pls ?
-
HI just built a annsman virus 3.0 and fitted a force .28 4.6cc engine after getting it to start the clutch bell started to smoke stopped engine felt clutch bell was very hot , any ideas why this is ? ( must be binding ) but I can't see why or adjust it .. any input appreciated with thanks
Mchaggis
-
.Their vary hard to setup for a first timer but you'll get use to it
Hi I own area nitro cars etc but this is the first build I've done and the instructions went very great but I'm hoping that between them and and input from members of this forum I'll get there lol
Mchaggis
-
Anthoop many thanks sorted it now was missing metal ball joints ' rear all built now post pic soon all so front built but seams not a lot of travel on the arms ' seams quite low .
Cheers
Mchaggis
-
Hi has anyone had experience of building a ansmann virus 3.0 , just started to build and now a tad stuck on building the rear differential unit with the ball joint the secures to the rear arm to the rear shock tower any pics or help would be great
Thank
Mchaggis
-
Thankyou Purcyp and Shudson done that now works didnt think of that again cheers guys
-
Hi
just bought a ftx frenzy fitted new rechargble aa batteries fully charged and the controller is dead , however fit normal duracel batteries and hey presto controller works fine has anyone else had this issue ??? tryed 2 sets of rechargeble batteries same result nothing put duracel in and ok ..
Thankyou
mc haggis
-
follow up
3 head bolts were loose tightened them up and fired and started ran . now waiting for glowstarter to charge
-
Hey mcdaddy2010 did u get the frenzy started ?? been tryin meslf for a hour no joy apart from backfire out the carb twice lol
everything charged good glow at plug using opitmax fuel at 20% any ideas ??
Thanks
mchaggis
How To Dispose Of Nitro Fuel
in General - Nitro
Posted
I used 4yr old nitro 20% fuel to start a fire every week at my partners work but word of warning once empty be carefull
When if you throw it on fire as I did went bang and flew about 15 feet in the air .
Mchaggis