ant b 4

I don't really want to split sorry,might sell it as a roller though

Hello I'm reluctantly selling my losi ,due to needing a 1/1 it's not many months old and not had loads of use tbf,I have the bodyshell(abit brused)and no rear arches as they won't fit with the extenders on.its just had a new top end kit and was sent to Scott finally to do. Losi 5t Pro mx 30.5 new top end. Ada billet manifold. 990 carb with bearing mod. Team chase carb filter. Dt1 low profile air filter. Bzm exhaust. Outwears on pullstart and air filter Hour meter. Showing 23 hours since the car and engine were new. Batalone mesh plate. Bartalone drilled clutch cover. Fastlane billet diff top plate. Killer rc super v3 killswitch. Killer rc 7200mah lipo. Savox 0236 steering servo. Full force throttle servo brace. Hot racing throttle servo arm. Ddm quick relese throttle linkage. Turtle racing front and rear chassis brace including front upper. Full force fuel line fittings. Darksoul fuel line quick disconects. Billit fuel line clamp, New 8000rpm lightweight clutch. Darksoul vented clutch bell holder. 20tooth pinion. Modified rc sealed and booted brake disks. Uber rc wheel extenders. Bartalone cage pannels. Hostile mxt tyreswith foams taped on stock rims with silverback v3 bead locks in and out. Stock tyres with foams taped and silverback v3 beadlocks on the outside. Ddm chrome shock spings front and rear. Blue silverback v2 monkey nuts. Team fast eddy servo saver nut and jam nut. Team fast eddy bearing kit. Futaba 3pl 3 channel radio system I also have a few spares for the car I will include I'm looking for

That does look ok tbf,I'd get one if I didn't have a gen one lol

That's smart

Hello im just wondering what my losi would be worth if i sold it, The spec is Losi 5t Pro mx 30.5 new top end. Ada billet manifold. 990 carb with bearing mod. dt1 low profile air filter. Team chase carb filter. Bzm exhaust. Hour meter. Showing 23 hours since the car and engine were new. Outwears on pullstart and air filter. Killer rc super v3 killswitch. Killer rc 7200mah lipo. Savox 0236 steering servo. Full force throttle servo brace. Hot racing throttle servo arm. Ddm quick relese throttle linkage. Ddm chrome shock spings front and rear. Turtle racing front and rear chassis brace including front upper. Full force fuel line fittings. Darksoul fuel line quick disconects. Billit fuel line clamp, New 8000rpm lightweight clutch. Batalone billet vented clutch bell holder. Batalone mesh plate. Bartalone drilled clutch cover. Fastlane billet diff top plate. 20tooth pinion. Area rc cv quick disconect fittings. Modified rc sealed and booted brake disks. Uber rc wheel extenders. Bartalone cage pannels. Hostile mxt tyreswith foams taped on stock rims with silverback v3 bead locks in and out. Stock tyres with foams taped and silverback v3 beadlocks on the outside. Blue silverback v2 monkey nuts. Team fast eday servo saver nut and jam nut. Team fast eddy bearing kit. Futaba 3pl 3 channel radio system

My fitter done just that,I've replaced it with the dt1

My Baka and losi both have 990 carbs,just prime a few times then a slow pull then a normal pull

Hello had this in a draw in my garage for a while,it was only used a few times. I have a couple of high capacity nimh batteries for an extra cost(can get pics of all the batteries if needed)

It sounds to rich,aswell if you've been running in the plug may be oiled up

I have a bzm on my 5ive and it's loud but not to bad,defo quieter than my dom on the baja

that goes really well!!

Even just a replacement 4xaa battery holder will do

Got a gt3b I haven't used for a while,so you can have it cheap

Looks good

get a new spring,it should be hard as hell to get them to mate

do you have a link for that please

that is an 8k wich i dont think are stock(or they wernt when i got mine) can you pull it apart ? adit just noticed your missing a third of your pad on the top,and also is the top pic a different clutch as the pads look new and the spring is black

hello on my asimba cr3p tx im useing the stock 4xaa battery holder put one of the connectors has came lose,can i fit a small lipo or even a nimh,what size would i need

The stock spring is a 6k (black)that will cause a performance engine to bog,fit a hpi 8k spring(red)

FTXvantage brushed

I bought mine from modelsport,but I'd get one from freeprawn as with the points you can get a killswitch

I prefere new as now ones messed with it

A 50 in a baja and 2 speed that will be epic

I don't like them modern fake minis,if it was one of the other rally cars that would be better. I might convert mine to have electric start tho if they sell it seperate

futaba 3pl ftw