lilllad83
-
Posts
1,273 -
Joined
-
Last visited
Content Type
Profiles
Forums
Prizes
MSUK-Forum - RC Model News and Community
Articles
Events
Posts posted by lilllad83
-
-
Very tempted
-
opinions please?
Was projecting 14 min runtimes at the neo16 after just being ran in round Ledbury the week before which it gave 11.5 min runtimes flat out!
-
Is that jar of sugar 1/10 or 1/8 scale!?
-
Parcels built up this week as busy at work..
Gt12 1s lipos
gt12 motor and esc
gt12 bearing set ceramic
lipo & life receiver batts
x2 hv 1268sg servos for xb8
1256tg servo for desc210
shoe goo
410 receiver
p5 novarossi an pipe
10 plugs
bearing sets for xray xb8 and xb9
Drive shafts all round for xray xb8
Cv rebuilds all round
Bag of anti roll bars for xb8
4mm bullets
14awg cable
receiver voltage monitor
Lipo/usb charger thing (dead handy)
centre diff bulkhead xb8
spur xb8
clutch setup jvd
clutch bell
Xb8 Shock bush sets x3
xb8 piston set
10m fuel tube pink
clutch bearings x20
starter box peg set
starter box switch
An arsy letter from the bank
Busy weekend ????
-
Change ur connectors oxidisation has probably built up making a weak join, happens to my revo every few months. If your cells are ok and ur esc ain't thermalling it must be the connectors :-)
-
If the receiver works u can get the esc apart, do so it won't hurt trying to dry it out
-
Take the receiver out, open it up and warm with hair dryer, look for obvious moisture. If you have a hump pack try powering up the receiver with a servo to see if it works, try both channels obviously. Think if it was the esc you would still have steering unless it proper ****ed it
-
Got a desc210 with servo for sale, 2 bodies and a few wheel sets for
-
Can I take the hudy handles lot please
-
Cornwall RC Racing near Helston
-
I'll take the 1256 pls m8, what's ur PayPal
-
Need to drill some new holes so i can sit the XB9 on with four pegs, as i'm using the fronts only at the moment.
-
Since this time last week the postman has been busy..
X-ray xb8 2015 (tired of my Kyosho breaking)
Full spring set
High def brake kit
Spare shocks
Clutch bearings
X-ray hoody
Hudy hat
X2 1256 servos
Spare drive train parts
Shaft pins
Air filters and oil
Proline pin points rims and insets
Answer x 4 clutch shoes
Answer x3 clutch shoes
Gallon of rb fuel
Glow plugs
Selection of Pistons
Silicone oil
and finally an overdraft warning from the bank :-0
-
Think ur Inbox is full m8
-
Have an rc8.2 nitro roller I'm selling for
-
Pit buddy, MORE dex210 rear towers, wheels tyres for said durango, spray paint, and some bills - gutted!
-
Today alas nothing :-( the last two weeks however have seen an X-ray xb9 arrive along with 2 savox servos, a set of mini pins with os rims, a new spur for said X-ray, a new dsmr rx, an alpha 852 .21, plugs, fuel tube, filter foams, varying oils and enough nitro to re-start a small planet rotating!
just need smr's website to kick back into gear and send me my starter box rebuild bits and I'm good to go for the pending club meet at frankly mcc on the 17th :-)
I'll find something that equals the handeling of this damn brittle kyosho mp9 if it kills me
-
Dude check race pace uk on eBay for spur -
-
I had the same issue some time ago now and I never did find a solution :-/ the best I could get to work was the rather unusual program card with pins and bridges etc but didn't have the option to change to/from training mode :-/ hopefully u find a solution and share with us .. And sorry for being totally useless lol
-
true that lolPrayer is the only answer.....
-
personally I've not had problems with lipos being damaged while in a car, for me it's usually when they are handled (or dropped more to point) or when they are lent to friends lol
strap em down and make sure nothing is too close to moving parts and all will be well unless u chuck ur ride off a great height lol That's all folks
-
After takin a look at the marauder use this link instead
No full on slicks but they are road tyres
-
http://www.google.co.uk/search?q=17mm+road+tyres+pre+mounted&ie=UTF-8&oe=UTF-8&hl=en-gb&client=safari#q=17mm+road+tyres+pre+mounted&hl=en-gb&tbm=shop theres a few to choose from it seems but would depend on the style/wheel size u want
-
Welcome :-) Proline and Schumacher both do slicks but would need gluing on some 17mm rims, there are brands that do pre-glued roadies but I'm afraid the names escape me.. I'll have a google and come back..
New piston and sleeve for my hot bodies Ohara edition os
in General - Nitro
Posted
Ok guys still have this engine, decided to run it at my last meeting on Sunday and the old girl got me qualified 5th in the A final!
Surely a testament to the os build and design quality!!! I would still like to rebuild her with new liner piston and crank so can anyone point me in the right direction for the parts please? Had a test repinch done on a lesser engine after my original post but the engine never performed the same so am reluctant to try this on the os as she's still a screamer! Just want the run time and precise tune back .. Any help appreciated thanks