MiRaGe112

Here for sale is my much loved Arrma Outcast 4s in bronze. I have owned this for a couple of years but hasn't had a great deal of use, only had about 5 packs through it. It's fully working with no known issues. Will be cleaned thoroughly before sale, can upload new pictures as required but used old photos I already have from when I was meant to put it up for sale ages ago! Does have a few marks and damage to front and rear bumpers but nothing is cracked and doesn't affect use. It comes with a toolbox of spares, the original Transmitter and receiver and a 4s Hardcase lipo. It features upgraded RPM front arms and GPM metal driveshafts all round costing £60 alone. Massive improvement to durability. Reason for sale is that I just don't use it anymore and I have too many RCs so need to thin the collection out a bit. Price is £280 ono, collection preferred but can deliver within reason or I can post at buyers cost. Will come in original packaging with all manuals/tools. Thanks for taking time to read my post 👌

Found some that fit, anyone had any experience with Team Orion batteries? Are they any good? https://wheelspinmodels.co.uk/i/332389/

Okay no worries, thanks for the assistance 👌

They've just arrived today, super fast postage by Amazon, can always return them if they are too big. Sooo close, reckon it may be too tight of a fit.

These are the ones I have ordered: https://www.amazon.co.uk/gp/aw/d/B0859BF3Q2?psc=1&ref=ppx_pop_mob_b_asin_title I have a feeling they may be too big 🤦‍♂️ 8 mins really doesn't seem like a lot for 5000mah. How disappointing 😂 Ideally I'd like EC5 connectors on the battery so I don't have to change anything.

I've recently just ordered one, won't be here until March but I honestly cannot wait 😊😊 I'm having a real hard time trying to find battery tray dimensions. Can't see them on the Internet anywhere. Does anyone have them to hand, or maybe someone that owns one would be nice enough to measure it for me? The length of the tray is the main concern for me. Thanks in advance 😁

Hello all, I am considering putting my Outcast 4s up for sale but am not sure how much to put it up for. - It has all the original electronics in it - Motor servo, esc and radio gear - RPM arms on the front - GPM steel driveshafts all round - Lots of spares included - Will come with 5000mah Hardcase 4s Lipo So if anyone could give me a guide on what sort of money I could get for this, would be much appreciated 👍 Was thinking somewhere around the £300 mark... Wasn't sure which category to put this in so feel free to move if necessary. Thanks for reading.

Last bump and price drop before going on eBay.

Cmon someone must want this, it's a great little truck, I'm open to any offers so feel free to ask 👍

Bump!

Price drop !

Here I have my Absima AT1BL for sale. I've owned this for a couple of years now and have to say it's been brilliant. I've only ever had to replace a diff case because I broke the body posts off and that is it! This thing is surprisingly tough. It comes with the standard 3421KV motor and a Leopard RC 60A ESC. It's crazy fast on 3s... Reason I'm selling is that's it's just no longer needed and I'm funding a new RC. There is nothing wrong with. This model has been discontinued now as far as I know but spares are very much still available for this. Comes with the standard Absima transmitter and receiver. Bad points - The front shocks have leaked out so suspension is a little soft and the front bumper has broken off but it doesn't affect the way it drives. I will clean it up before packaging and sending. The cable tie is just there to help keep the battery in place. So the price I'm asking is £110 posted but am willing to negotiate so give me your best offer... Thanks for looking 👍👍

The cables into the charger or the battery? Thanks

Here I have a short video showing an issue I have when charging certain lipos: https://youtu.be/QwuiPvbkYJE This is my 6s 4000mah lipo and it won't seem to let me balance on anything higher than 2A, and won't let me standard charge over 3A. Now I'm not sure wether this is a charger fault or a battery fault or if it's just nothing to worry about 🤷🏻 Some of my lipos will charge at the full A rating, I can balance my 2s and 3s at 3A and they're fine but when I charge my 4s and 6s it doesn't seem to like it. The amps seem to fluctuate when charging too, occasionally dropping down to 0.1A. So is this normal? Or do I have a problem with the charger or the batteries? Thanks for taking time to read, any help will be much appreciated 👍 Regards.

What's the lowest you'd go? Where abouts are you located also?

Think I might try dropping down a size. It's getting hot enough that I can't hold my finger in it for more than a second... Bearings are all okay from what I can tell, I would've thought 13t would've been fine but maybe not. I've set the mesh right too. Think I'll try a 12t and a heatsink, cheers 👍

Just bringing up this thread again, not sure if anyone here still has STs but what pinion size would you guys recommend for a 52t pinion, got a 13t on at the moment with a 2200kv motor and it still seems to be getting really hot? Do I need to reduce the spur gear size? Thanks

I've been looking at the Fastrax 1/2 offset wheels and tyres but they're out of stock everywhere 🤷🏻

As title states I'm after some 1/8 Truggy dish wheels yellow or white preferably, anyone help me out? Thanks

Still after a bodyshell, why is this so hard to find one? 😂

Thanks for the tips guys 👍 I just think I've been a bit unlucky with this one. For one I've watched people sending these things over massive jumps and they just take it. Maybe it doesn't like the fact I'm being too soft with it 🤷🏻 It's an awesome truck when it's working, and I still do have love for it but it's honestly costing me a fortune at the moment. I can understand parts breaking if it's being launched off ramps and on rough terrain but In all honesty, the way I've been using it is the nicest way this truck could be driven... I'm gonna fix what's broken now and see how I get on. If this continues you will be seeing it up for sale 😆

So I've had my outcast for about 2 months now and I can honestly say I've never owned a worse RC than this. Just constant problems one after another. First all the transmission melted because the slipper kept coming loose. So I spent £££s fixing that... Now the driveshafts keep popping out, so I thought I'll buy some brand new ones to hopefully sort the issue. I've gone to replace it and the bolt has snapped in the diff due to the amount of thread locker in there. (See photo) Really Arrma?? Spend £400 on an RC and then having to spend £100s fixing it when all I've done is run it in my back garden and up and down a field. This thing hasn't even seen any dirt or air yet because it's constantly going wrong. Everyone says how good these trucks are but clearly they really aren't 😆😆 Anyone else had issues with these or is it just me? Not sure wether to keep fixing it or just sell it? Literally had enough of this now....

I'm after a cab forward design really, does anyone know if something like this would fit? I mean how different is the RC8T to the RC8T3?https://www.cmldistribution.co.uk/product/AS81324/team-associated-rc8t3-pro-line-body-with-mask#description

As title states in currently trying to look for a new bodyshell for a Hyper ST brushless I just purchased. Not a big fan of the standard shape. I know that the Proline Bulldog shell in RC8T and D8T format fit, but really struggling to find anywhere that stocks them as they are all discontinued now. So does anyone have either of these for sale or know of any newer model body shells that may fit? Thanks for reading guys 👍👍

How much as a roller?