flatout!

Has he sold the bzm pipe? That's the pipe you want with it if he still has it Mad for powerful motors Sent from my SM-G900F using Tapatalk

Not sure on the measurements tbh! Measure the pipe on the header and purchase pipe on that measument Damon tweeks is a good place to start and you need a heat proof silicone pipe with stand the heat Coz on eBay they will sell you anything not knowing what it is that you'll be needing it for, You can get reduces bends, and all sorts of lengths colours lol! Other than that just ask on ebay ask the seller's and tell um what it is your wanting it's got to be 300

If its off scoob you'll be ok he knows what he's doing with um, You only need to look at his baja to know that. it's mint! Don't think you'll go far wrong Sent from my SM-G900F using Tapatalk

I weld mi sen and yep it's a art in it Sent from my SM-G900F using Tapatalk

Iv got some black same size and it's got a bend in it to go onto that header I sent ya with the exhaust! Thing is I use it to fill mi van up with desiel lol! But you can have it if you send the

Hay Andy iv seen these 4x4 done in road going tackle and they look very capable, They drop um to the floor and they look good, not see one perform yet but I bet they'll handle well

Iv not got owt on pal it's just the reeds got a bit to much power and it's tearing it's self apart a bit to often lol! But I wouldn't mind seeing what power I could get out a 23cc tuned zen Sent from my SM-G900F using Tapatalk

Show us some nice stainless welds

Just leave the thing on ya baja run it till its piping hot! put some chips and a bit of veg round it and get it nice and warm jobs a good Un lol!

Hi matey. Is it a second hand engine? Or new? Is it a reed or a piston port? But iv got a clone dom on and it's ever so good for my reed cased engine! But iv known the victory side pipe to used too, If you do get a pipe I'd go for a clone cos the good named pipes all split coz the wall of the steel is so thin for the tuning of the pipe. it's difficult to weld to as iv done it on a few, If you get a clone the wall of the steel is a lot thicker and easy to get welded up if you have to They do victory clones and others too

Thanks pal been looking and didn't find owt I could trust anywhere, And where would you suggest getting it tuned?

Looks nice! Mines got some nice colour from doing the same thing

I get ya! Do zen do a 23?

Is it the old stop botton that makes that obvious dave?

To stop the shock bottoms snapping on me iv gone for the shaft upgrade. 8mm shafts and you can use the seals off you old shocks! The stock ones will stand it until you land it funny,front heavy usually does it and iv snapped back us too, iv got 8mm shock shafts all round and there good and iv got a really thick oil in there, 60wt it's like treacle it's that thick Ut that's how I like it, I can drop my baja from my head and it'll not bottom out, I'd not advice you to do that on stock set up, it'll probably shoot straight through and land on its chassis lol! It's a great mod to do to the stock shock body's but don't forget you mote like it all sloppy I don't no but if ya want some links I think it's on my list somwere and its a cheaper mod and better in my opinion than paying out for big bores and so on! I feel the smaller shock gives you a more precise adjustment and you have also the option to get the harder springs to. Witch I have on the rears for that bit extra weight on the rear! You don't want the front bouncing all over the place you end up with no steering g coz the front wheels will be always in the air lol! Fronts need to be planted all the time. Or your going to end up in the nearest hedge

I bought one of the older lot of them 002b it had 5b monster tyres on it, bright orange lol! And I mean everything was orange! it looked like it had crashed into B&Q's paint department lol! But it was a decent chassis, engine isn't bad and it's a good start to 5th scale I bought the 002c the 29 ported and wasn't that much different to the one you've got in the 002b, It's just about stripped if km parts now but they held up for about 4 months of punishment and I meet punishment as well I drove it hard. Both come with wheel extenders stock, and the suspension is bang on! Set up well to start with but soon as you start jumping it they soon let go, they snap the bottoms quite easy so take it steady till you get an upgrade on um, But apart from all that just go and enjoy it and take ya time with it!

Stop fiddling with it its fine! lol! My Mrs wishers she was a baja! I'm always fiddling with it pmsl!

I had a km 29 ported and a stock 26 yama buggy engine was quicker more powerful and lasted longer to There porting is none existent iv taken the 29 ported head off and there's nothing any different lol! But the 26 yama engine is a lot better all round 26 2 bolt over 29 ported But that's my experience

I wouldn't run it to the point of death lol! Ideally change before its starts loosing power, you could wear the barrel out doing that, just keep an eye on it smoking nore than normal and get a tto hour and rpm meter on it, then you'll no exactly what hours its run and what rpms your getting, That's not important really to start with but you can relax on how many hours its run, Wish id taken my advice and bought one, I haven't a clue what my reeds done hours wise lol! But yeh get one kid you'll not go far wrong to when to up to your 26

If I can't put mi nut on with mi fingers theres somthing wrong, so I take a look and if it dosnt go on its somtimes a bit of muck wire brush jobs a good un sorted, But id never wind um on with a socket on mi ratchet not a chance, finger tight and then nip it up with the 24mm socket and driver

Re thred um kid, its only alloy

Dam right iv got mi tablet! Screwed without it,

Im at the manx kid iv got some wifi kid, no stopping me now lol!

Still going, but you'll be lucky to get owt in a hurry, my mates been waiting months for a 6 port reed case piston, Its rediculess having a [email protected] but having to wait for it to come from the states wtf!