rcrallyuk
-
Posts
616 -
Joined
-
Last visited
Content Type
Profiles
Forums
Prizes
MSUK-Forum - RC Model News and Community
Articles
Events
Posts posted by rcrallyuk
-
-
Hey.
I am looking to clear out all my Rc stuff.
I have posted these on Ebay so i will keep this bit short. I don't have any ideas on how much this stuff is worth so i will let people know how much i would like but i will be open to offers.
As mentioned. These are listed elsewhere so they can be removed at no notice but if i am in discussion with someone. I will follow this up.
Pics will be at the bottom
Prices:
Tamiya TT01:
-
That looks not bad. I have seen the crankcase for the 3.0 so i might be able to get away with that. Its split just under the head so i can use that and i just hope there has not been any damage on the Piston. It gives me a chance to shave a bit off it
-
Hey guys. My engine has just died. It's slit in half. So I'm needing to get a new one. It was a hpi wr8 g3.0. I. Have looked online and I could get away with just the crankcase. Does anyone know what I need to look out for to see if I can pick up another brand. And if anyone has a spare engine that would fit. Let me know
-
I want to cry. Got the car down to my. Big ash field. It was running amazing. Went to fill the tank and it just popped. Tried to start it and the full engine had split. Right below the cylinder head haha. So can anyone recommend a replacement engine
-
Strange because on the parts list at the end it doesn't have the b020 code for sizes.
-
Aw right. No bother. Thanks for the update. Can't wait to take the bad boy out tomorrow. Hopefully it will be a steady run and I can get some tuning done.
-
I never ever knew those wee tiny bits were there. We'll I have now just had to email the company back and apologies as I am a took and they are the perfect size haha. I hate this hobby sometimes.
-
That's what I though. J.a. Doesn't look like it though. Another thing is that I got a new set of front uprights and the m3 screw home for the top and bottom are too big. I think they are a 3.5. Anyone had this before. It's genuine hpi bits.
-
Hey I picked up a set of bearings online based on the manual. It said I would need b020 and b021 the 020 set is the ones for the front uprights x4 and the 021 apparently we're for the rear uprights but I the front and back are both the same bearing size (020) so I'm a bit lost. When taking the uprights apart. I saw there was a small spacer in between the internal and external bearing. Could this be the 021.
Thanks.
Oh and no response in regards to the 3.0 clutch bearing. I'll email them again.
-
Haha I ran my car the other day with the old crystal set up on the stick controller. Not good lol.
-
Haha. Next time you will wrap it in a wee sandwich bad with a cable tie. Saves a lot of pennies.
-
Any matt?
-
My 23't was playing up with the Modelsport ESC set up...silly, but i just swapped the polarity of the motor (swapping the cables about that run to the ESC - might have to reverse the trim on TX)
-
Ill PM you buddy
-
hey mate.
im in need of the front carriers here: http://www.ebay.co.uk/itm/271544751219?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
and just the uprights here: http://www.ebay.co.uk/itm/371122929322?_trksid=p2059210.m2749.l2648&ssPageName=STRK%3AMEBIDX%3AIT
if you have B020 and B021 Bearings at all, its the rear set ones.
Thanks
-
Anyone driving a WR8 or a Bullet. Doesn't matter about 3.0 or flux. I just need to see if i can get a hold of some parts.
-
Thanks. I need to drop them an Email anyways, so il ask and see what they say.
-
1
-
-
I'm needing to get a set of 4 bearings for the knuckles. I get my tamiya ones from a guy down south but he doesn't stock wr8 remakes. Can someone tell me where the best place to get them at and are the 4 of them all the same size?
-
Hey mate. Strathclyde Park sounds like a winner. That would be good if we could meet up and if you would help out that would be great. I only know the main bits of the park.
-
OK so spent a bit of time with the car tonight. Got it running well. The car responded well after warm up and a good half throttle run. When taking to full throttle. The car would do it and then loose power. I ease off the gas before it stalls and I am able to keep it running. Any ideas what the problem is.
-
Hey.
Im looking to organise a Rally event in Scotland. Im looking for some location ideas.
What i am looking for: I would need an area of (minimum) half a football pitch that is loose gravel and some tarmac or a good forrest that has some great "rally like tracks". The event will only be help over one day so electricity would be good but not needed and it would need to have good parking.
We are looking to have a full rally track and a rallycross section (if we can) that we could build some jumps and a nice track.
Any help would be great.
I have a couple of ash football pitches near me that the council have said i can use but they said i cannot mark the ground and its just a bit close to a main road. Its also in a housing estate and im hoping to attract some nitro guys for the rally cross so i dont really want that.
Cheers.
Andy
-
How much bell rattle do you get off your ts4n
-
I should have the parts for the wr8 by then so I'm game. I might need a bit of help with tuning. I just got into nitro and I know the car can run a lot better.
-
Nice one. What time you heading up at. I only have 1.10 cars a day my wr8 is awaiting parts. Would it be OK for 1.10 cars
TT01, TT02 or large-scale
in Wanted
Posted
Hey. So I have been out of the rc game for a while but I'm looking to get back into it. I am looking at either TT01, TT02 or large-scale. Ideally as a rtr but something just to get my fingers twitching...
Let me know what you have
Andy