jappa

bump

i,ve got loads of revo spares for sale now i have the baja.most are new and a few are used Gtr shock rebuild kit 5462 Clutch rebuild kit 5352 Fr and rear bumper 5336 Spur 38 th 3954 Spur 36 th 3953 Rocker arm prog 2 5358 Gear set wide ratio 5384 Axle carriers 5334 Pivot balls 4933 Body clips 12 1834 Used brake disc 5364 Spring throttle return 4056 Front skid plates 8x green seals bearings 2 hub adaptors? (I think.they are the pieces with the blue rubber boots on them and hold the wheels.) 1x silicone oil 4x wheel hexes few rod ends used bits primary gear 4995 idler gear 5337 diff carrier 5381 40t gear for 2 speed 5383 output shaft 5369 clutch bell 1 random gear 1 steering servo arm diff shaft? revo stainless steel screw kit.about half full,maybe a bit more loads of random screws,a few nuts,springs. looking for £85 posted will not split as it would take weeks to sell off also for sale is a unused set of 17mm wabash wheels in yellow with a set of nearly new bowties looking for £35 posted will put pics up tomorrow or pm if your interested thanks

bloody hell mate,small world its jappa here from e36coupe what car have you got mate(sorry for th hijack)

is the slipper clutch tight emough?it should be nearly full tight and then loosened off a bit.if it revs up without going anywhere it could well be that.

ive got a spektrum dx3 and find it very good.i havent noticed it going out of range nd taking too long to respond either. £135 at modelsport or £155 with an extra receiver

come down to essex mate to 'the quarry'

i think its sorted now.i took off the carb and had a good look to see what the idle screw actually does.it doesnt actually do anything inside the carb,what it does is adjusts the position of the throttle arm.i must have unscrewed it too much and it was no longer holding the arm so when i braked it automatically ulled the throttle arm the wrong way. i put it all back together,all at factory settings and got it running on a stand(old table lol) here i could actually play around with the idle,lsn and the throttletrim on the transmitter without actually driving the car up the road. it seems fine now.i havent touched the hsn and cant really until i drive it properly.a quick drive around the garden saw it act very peppy.so it should be ok now. you need to get one mate.they are true monsters.40mh doesnt sound fast compared to a nitro which does maybe 45 however they are bloody fast(i have an ss) on loose gravel its actually hard to kee it in a straight line after turning. i love it and am going to get the rear dom pipe for a bit more power

ive got all the filter off but cant see any opening or closing going on in the carb which bit should i be looking at.all the screw seems to do is move the little arm it sits on.even if i move the screw all the way in or out it seems to not actually do anything inside the carb

thanks for that i,m going to do it right now

well its a hpi baja so this may get moved. basically i ran it yesterday for the first time after running in.i tuned it and it ran perfect. today i went out and foolishly played with the settings.messed them up(must have been too rich as the plug was blacked up with carbon deposits) got it home cleaned the plug started it up outside my house and it ran away even with failsafe on. so sorted that and went back out. the car was now back at factory settings(although not the idle as i cant find that out). started it up and it revved up like mad.couldnt drive it.tried adjusting the idle but it made no difference,only richening the lsn made a difference,doing that made it idle (for all i know the actual idle is so far out and thats why i can only adjust with the lsn) ok so now its driving.very boggy (obv because its so rich) turning the lsn leaner only makes it idle like mad. however now when i touch the brake it pulls the throttle on the carb to the right(not sure if its meant to do this) and stalls the engine. the servo is set ok. the brake has never really worked no matter how much i adjust it. just took it outside to try again and now i can just about get it to keep idle but when i rev it the wheels barely spin you see for someone in the know its probably very basic to fix but for me i could be trying loads of things with no success.my idea is to give it to someone get them to set the brake up,set the tuning then i wont have to adjust the tuning unless i get another exhaust or something.

actually upon checking it was wheelspin models.are they any good? your right mate about lhs.the problem i have with them is they are bloody dear and only interested in selling me more bits.i may trey though as imo what needs fixing is basic.i just cant get my head round it

i,m sure on their site they had a page saying they will service your rc car for you.i can,t find it now i,d like to send them my baja as i just can not get it to run right or brake properly. i think i,m correct in thinking that if they tune it for me i wont need to touch it again

due to purchase of a baja i,m selling my nearly new revo 3.3. bought for me by my gf for xmas so its only a couple of weeks old. the engine has had just under 1 gallon run through it and was ran in to the letter. comes with all the gear you get in the box plus the traxass front and rear pushrods (cost £14) a new crowd pleaser 2 shell painted in metallic purple and white.only ran once with this shell so is basically mint exept for a small scratch on the roof. ( cost me£35 inc paint) pretty bashed up standard shell proline velocity wheels with (not sure which) tyres wheels are a bit scratched up (cost me £60) standard wheels fuel bottles x2 battery and charger un fitted extra wheel base rear arms (cost me £10) a few spares including rod ends screws 3 airfilters total plus a few other bits kicking about. venom temp gauge with voltage display and also is a failsafe cost me £50 2 3232x plugs (cost me £8) glow plug heater,glow plug tool (cost me £15 with second bottle) car,batterys,charger and fuel bottle cost me £395 total package tere cost me £587 plus te few spares i have too so around £600 worth te underside skid plates are scratched up but otherwise mint and straight.always followed afterrun procedure i,m looking for £400 posted or £380 collected can place this on ebay(98 with 100% feedback) for your security as i,m obviously new here few pics

i,m 99% sure i,m going to get a baja. however after reading the baja forums it seems that theres loads of bits which need replacing. change shocks to phatdaddys because the standard ones are crap some sort of guard round the engine to stop crap getting in uprated elcon clutch and arrier which seems to be around £100 at least some sort of mod to the hubs to stop the wheels falling off suspension arms easy to break and after looking at uprated ones it seems a full set is around £200 and a few other bits i,ve now forgotton are they really that weak or are they hardcore bashers thought i,d post here to get a more unbiased view cheers

pm sent