Jump to content

Nitroholic

Members
  • Posts

    17,644
  • Joined

  • Last visited

  • Days Won

    115

Nitroholic last won the day on December 20 2023

Nitroholic had the most liked content!

6 Followers

About Nitroholic

  • Birthday 09/01/1968

Profile Information

  • Gender
    Male
  • Location
    North London
  • RC Cars
    see signature
  • How did you find this forum?
    Found it free in a packet of breakfast cereal

Recent Profile Visitors

23,261 profile views

Nitroholic's Achievements

Proficient

Proficient (10/14)

  • Commited Rare
  • Piece of Furniture
  • Dedicated Rare
  • Week One Done
  • One Month Later

Recent Badges

4.2k

Reputation

  1. No. I wouldn't. The only reason for fitting a hard steel pinion is because a steel spur gear would tend to cause excessive wear on a brass one. Acetal won;t do that... but the harder pinion might cause issues with the spur, especially if your mesh is not 100%. It's also just not necessary. I try to avoid curing problems I don;t have when it comes to RC's, as you can often end up causing stress and issues elsewhere that you weren't expecting.
  2. Welcome aboard 🙂 The Grasshopper is a fairly simple build, and a pretty old design, but I totally get the nostalgia. I keep getting the urge to build a Lunchbox, which is similarly dated, only I would have to try and rectify it's worst design flaws. can't help with a drift car, as the only Rc I have done any 'drifting' with was a Baja 5B, which on loose dirt was quite capable going sideways!
  3. If you mesh it right....a steel spur isn't necessary unless you are getting issues with stones and grit getting under the shell andruibibng your spur. Had this bigtime on a mini Losi, which had a natural stone trap! Personally, a steel spur gear is a last resort....so I would start with the acetal one, and only go steel if I stripped it. Also important to make suire your pinion is right for your spur gear material. A steel spur eats a brass pinion.
  4. Not sure exactly where it is you are putting this grease, but I have used lithium grease in many a gearbox on RCs. The only place I would not use it is where it will come into contact with grit or dust. The stuff gets trapped in the grease and turns it into a fine grinding paste. Inside a sealed diif, though, I would use decent quality silicon diff oil.
  5. Depends what you are looking for. If you want a new Baja, get a KingMotor clone. They are the nearest thing to the real thing out there. Having owned both, the only issues I had with mine was down to prep work and the fact I bought the absolute cheapest one they did as I was going to swap a load of parts anyway. Sincew then, they have started putting better bits on and generally upped the spec a bit. I still wouldn;t buy an all alloyed one though, as they put things on that I simply would NOT have alloy. There were minor changes in gearing which meant gearboxes were not compatable, and they used to ship with some pretty awful servos. The gearbox worked fine ( once I replaced the diff oil and packed the housing with actual grease) and I replaced both servos with much better items. I think the newer KMs come with servos that are far more usable than the cheap toy ones I had back then. The shells were clear ABS though, rather than lexan. They do a 5T version, but you would have to be careful with the body. These guys: https://www.rcmodelz.co.uk/ are the importers for both the buggies and spares. The entry model KM001 now comes with a proper Walbro carb ( not the awful clone carb). alloy diff, reasonable shocks and a tuned pipe. Then you can just sit back, open the wallet, and upgrade from there..... They do a load of Rovan clones as well, but I have never tried one. They used to be rubbish. Might be a lot better...but I don't honestly know. I have only owned KM and genuine HPI.
  6. Bit confused here.... if it wasn't sparking, the engine would not run. In your video...it's definitely running. If it has stopped running and won;t restart...take your plug out and give it a check. It's colour and condition will give an indication of what is going on. What 2 stroke oil are you mixing with the petrol? and to what ratio? That can also have an impact on the plug. Now.....drive from the motor uses a centrifugal clutch to drive the gears. It could be worn or damaged. Also worth checking to make sure all the gears are fully meshed, and that there are no loose grubscrews in the wheel squares at the back. Anything slipping will soak up the power as the diff sends power to the path of least resistance. It's working, or it wouldn;t move...but unless your motor is shot, it should move a bit more readily than it is.
  7. And don't worry about soldering close to a LiPo battery. Unless you literally stick the soldering iron into the pack, it;s not an issue. The cells are joined with big soldered tabs when packs are asembled, and it's not a problem. I have soldered connectors to LiPos many times. Still on zero fires. Heat shrink is a must, as is making 100% sure you have the wires connected the right way round. Also, as Stormbringer mentioned, heatshrink is a good idea. You do not want exposed wires that could short the battery. That would kill the cell
  8. we just want to let you know how it can start with asingle micro heli..... and....grow. quite a lot!
  9. That's the micro collection. I have a 120SR, plus some non Eflite helis and a Nano-CP. The tandem was a bargain. Came as part of a badly dezscribed job lot on E-Bay along with a construction set of those cast your own blocks to build model houses. Normally they go for around £80 when they show up on E-Bay, but that is rare. Left to right.... MsrX , Msr, Msr with an S300 canopy modded to fit, mCX2. 3 mCX, mCX S300 and the tandem twin. Have the boxes for most too. Probably have enough spares to put another few together. Have a white body set and stickers, which might go on one of these.
  10. These were a pretty poor clone of a rather poor old buggy. The motor layout is similar to that used in the onroad FG cars, which limits what you can do for an exhaust. They also shipped with awful carbs, which should be swapped for a proper Walbro unit if it hasn;t already been done. For shocks, FG ones are probably as close as you will get. Measure the length, and shop for something similar. The fittings should be close enough to work without much effort. You really should have a brake setup. Again, it looks a bit similar to FG brakes. Might be possible to work out something there.
  11. Started with a Blade mCX .... then mSR then micro CP and a 120SR. Haven;t gone up sizes from that as I was a bit restricted in terms of where I could fly. Have built up a collection of mCXs..... Have a stocker, one S300 version plus the Tandem Twin. Well, actually, I have 4 mCX in flyable state plus a load of spares. Got 2 mSR's and an mSRx plus spares. I bought a few job lots off E-Bay, so I have frames, booms, boards, landing gear, bodies. Most of the fixing they have needed to get flyable was cleaning up or replacing servos. I have a decent sized garage to fly indoors, which is handy when the weather is bad. I have a couple of cardboard 'heli pads' that I put in various locations and fly circuits. It's good practice for flying 'nose in' Got my first mCX not long after they came out. Saw one in the local Hobbystore, and the guy had a demo to try. He lifted off, put it into a hover....then put down the control and it stayed put. That level of stability was perfect to learn the basics. OK...he was just showing off really, but the thing was, trying to learn on a twitchy heli might get you better skills, but it won;t get you flying quickly.
  12. Anything is possible. Can it be that difficult? Sure can. Depends if there is a ready made motor mount for you to use. If there isn't then you will have to either modify another mount or your chassis to accept it. Then find a battery tray and somewhere to mount the ESC. How hard that is depends on you, the tools you have available and how close in terms of dimensions the centre diff mount on your buggy is to one for which mounts are available. of course.... Google helps... https://www.eurorc.co.uk/page/28/how-to-convert-xray-xb8-into-xb8e
  13. That's a bold styling statement. and an interesting pricepoint. Put those two together, and you have a recipe for a truck that will stick to the store shelves like a limpet.
  14. I do still have all the M5 part STL's. I think they are the final versions, but some may not be. Plus there are some parts with multiple versions. You would need to sort through them to work out exactly which parts are needed. The exhaust and the radiator are straight forward. I also made replacement aluminium sideplates. There is a load of pics I took which show the plates and how they sat on the bike. Should be possible to work out what you need from what I have. edit: I have uploaded the files/images to a free upload file site. Will be there for the next couple of weeks. https://easyupload.io/w4fl9f
×
×
  • Create New...