Jump to content

rcrallyuk

Members
  • Posts

    616
  • Joined

  • Last visited

About rcrallyuk

  • Birthday 26/02/1988

Contact Methods

Profile Information

  • Gender
    Male
  • Location
    East Kilbride, Glasgow
  • RC Cars
    Tamiya TT01 Rally. Tamiya TGS and HPI WR8
  • How did you find this forum?
    Google

Recent Profile Visitors

1,003 profile views

rcrallyuk's Achievements

Apprentice

Apprentice (3/14)

  • Collaborator Rare
  • Super Collaborator Rare
  • Reacting Well Rare
  • First Post

Recent Badges

26

Reputation

  1. Hey. So I have been out of the rc game for a while but I'm looking to get back into it. I am looking at either TT01, TT02 or large-scale. Ideally as a rtr but something just to get my fingers twitching... Let me know what you have Andy
  2. Hey. I am looking to clear out all my Rc stuff. I have posted these on Ebay so i will keep this bit short. I don't have any ideas on how much this stuff is worth so i will let people know how much i would like but i will be open to offers. As mentioned. These are listed elsewhere so they can be removed at no notice but if i am in discussion with someone. I will follow this up. Pics will be at the bottom Prices: Tamiya TT01:
  3. That looks not bad. I have seen the crankcase for the 3.0 so i might be able to get away with that. Its split just under the head so i can use that and i just hope there has not been any damage on the Piston. It gives me a chance to shave a bit off it
  4. Hey guys. My engine has just died. It's slit in half. So I'm needing to get a new one. It was a hpi wr8 g3.0. I. Have looked online and I could get away with just the crankcase. Does anyone know what I need to look out for to see if I can pick up another brand. And if anyone has a spare engine that would fit. Let me know
  5. I want to cry. Got the car down to my. Big ash field. It was running amazing. Went to fill the tank and it just popped. Tried to start it and the full engine had split. Right below the cylinder head haha. So can anyone recommend a replacement engine
  6. Strange because on the parts list at the end it doesn't have the b020 code for sizes.
  7. Aw right. No bother. Thanks for the update. Can't wait to take the bad boy out tomorrow. Hopefully it will be a steady run and I can get some tuning done.
  8. I never ever knew those wee tiny bits were there. We'll I have now just had to email the company back and apologies as I am a took and they are the perfect size haha. I hate this hobby sometimes.
  9. That's what I though. J.a. Doesn't look like it though. Another thing is that I got a new set of front uprights and the m3 screw home for the top and bottom are too big. I think they are a 3.5. Anyone had this before. It's genuine hpi bits.
  10. Hey I picked up a set of bearings online based on the manual. It said I would need b020 and b021 the 020 set is the ones for the front uprights x4 and the 021 apparently we're for the rear uprights but I the front and back are both the same bearing size (020) so I'm a bit lost. When taking the uprights apart. I saw there was a small spacer in between the internal and external bearing. Could this be the 021. Thanks. Oh and no response in regards to the 3.0 clutch bearing. I'll email them again.
  11. Haha I ran my car the other day with the old crystal set up on the stick controller. Not good lol.
  12. Haha. Next time you will wrap it in a wee sandwich bad with a cable tie. Saves a lot of pennies.
  13. My 23't was playing up with the Modelsport ESC set up...silly, but i just swapped the polarity of the motor (swapping the cables about that run to the ESC - might have to reverse the trim on TX)
×
×
  • Create New...